| Home > LNBF > FTA LNBF > KLB1 | Can't get everything you want off of just one satellite? Then the KLB1 is for you! This single output, duo satellite lnbf is capable of receiving two satellites that are 4 degrees apart at the same time, making it the recommended solution for the customer that needs two satellites, but doesn't want his yard to be overcrowded with dishes! It also boasts an incredibly low noise figure of 0.4db, meaning you get exceptional picture quality and high signal gain! You want to receive signal from two satellites at the same time? The Sadoun DUO LNBF is a Monoblock KU-band linear LNBF: - Digital satellite reception of two satellites separated by 4 degrees on the Clarke Belt arc.
- Commonly used with Satellites 101W and 97W, or 97W and 93W in North America
- Built-in DiSEqC Switch
- 0.4 dB NF Connects to one satellite receiver
- Works on offset dishes between 60cm and 90cm.
The
LNBF on each side of this Monoblock Duo is a UNIVERSAL type. The built-in DiSEqC switch allows the receiver to switch between the two satellites instantly. This is used for Free To Air satellite reception in North America. Compatible with all FTA satellite receivers on the market today. Works with all KU band reception except DSS. Great choice for Galaxy 25 and AMC4 simultaneous reception. Or Galaxy 25 & Galaxy 26 reception. FEATURES: Single Output LNBF Lightweight and small size for easy installation Covers Ku Band Satellite Frequencies 10.7-12.75 GHz 0.4 dB low noise figure for improved signal reception (specially on weak signal) and low interference. Voltage-Controlled H/V Switching (13/18 V) Comes with an adapter for any dish with LNBF holder standard 40mm diameter. Thus allowing this LNB to be mounted effortlessly on almost any offset dish, such as Fortec Star 80,90cm dishes. Black LNBF Holder you see in the picture above is not included. Linear type. COMPATIBLE WITH ALL FTA SYSTEMS RELATED TO Galaxy 25 (97W), G3C (95W), Galaxy 10R (123W), AMC4 (101W), and more. 2 Year Mfg Warranty
Instructions Sheet Installation Instructions: Place LNBF1 in the focal point of your dish using the Dish's LNBF holder. Connect an RG6 coaxial cable between receiver 1 and LNBF Monoblock Output 1 Connect an RG6 coaxial cable between receiver 2 and LNBF Monoblock Output 2 Set the DiSEqC switch position in each receiver as follows: Optimize the signal strength and quality for LNBF1. Optimize the signal strength and quality for LNBF2 by turning it a little upwards or downwards a few degrees.
Specification | Value | Input Frequency Range | 10.7 ~ 12.75 GHz | Output Frequency Range | 950 ~ 1450 MHz | LO Frequency | 9750/10600 GHz | Conversion Gain | 56 dB | Cross Pol. Isolation | 25 dB | | F/D Ratio | 0.6 | Noise Figure | 0.4 dB Typ (0.8db Max) | | Load Impedance | 75 ohm | Input Reflector Type | Offset | Gain Flatness | 5 dBpp over operating band +/- 0.5 dBpp H/V.Pol @ 27 MHz | L.O. Frequency Stability: (+25°C) | +/- 1 MHz | (-40°C ~ +60°C) | +/- 3 MHz | L.O. Phase Noise: (1 KHz Offset) | -59 dBc/Hz | (10 KHz Offset) | -84 dBc/Hz | (100 KHz Offset) | -101 dBc/Hz | | L.O. Spurious | -60 dBm | | Omage Rejection | 40 dB min | | Output VSWR | 2.0:1 | Output Connector | 75Ohm F Type Female | D.C. Power Supply | 11.5 – 19 V | | Current consumption | 90 mA Typ., 110 mA Max | Polar Switching Voltage | Vertical: 10.5 ~ 14.5 V Horizontal: 15.5 ~ 21 V | Operating Temperature | -40°C ~ +60°C |
|
|
| |
![[ Super Buddy ]](../../Products/Virtual_Rock/superbuddyspecp_small_small.jpg)
