Sadoun Satellite Sales Logo
AStarBid.com
We Sell Wholesale & Retail
Order Online or Call us at 1-888-519-9595 or 1-614-529-9560
Search
Installation FAQ
Wholesale
Forums
ViewCart

 1- SATELLITE BUNDLES

 2- RECEIVERS

 3- DISHES & MOUNTS

 4- LNBF

 5- SIGNAL METERS

 6- HH MOTORS

 7- SWITCHES

 8- HEADEND / VSAT

 9- SUPPLIES

 10- AV ACCESSORIES

 11- REMOTE CONTROLS

 12- OTHER PRODUCTS

Home > Motors & Dish Movers > Positioners

Positioner

1 VBox 7 DiSEqC Positioner front

VBOX 7 Actuator Controller (positioner): This is used to position your C band dish. It takes DiSEqC commands from your satellite receiver and converts it into 36V pulse and sensor to store positions - can store 99 Positions. It can work as a stand alone positioner or it can accept DiSEqC 1.2 commands from a satellite receiver. Controls and displays position. Remote control Included.

Out of stock - no ETA

2

Top Choice

 

Sadoun PowerTech V3000 (V-Box III)

V3000 (GBOX) SatHawk PowerTech Actuator Controller (positioner): This is used to position your C band dish. It takes DiSEqC commands from your satellite receiver and converts it into 36V pulse and sensor to store positions - can store 99 Positions. It can work as a stand alone positioner or it can accept DiSEqC 1.2 commands from a satellite receiver. Controls and displays position. Remote control Included. Regular Price $79.00

Out of stock - no ETA

 

Wiring The Actuator (wires not included with actuator):

The actuator line is comprised of five stranded copper wires.

  • Two 12 or 14 gauge stranded wires are used to power the motor and

  • Two color-coded 18 or 22 gauge shielded wires connect to the sensor.

These actuator wires should be connected to the appropriate terminals on the back of the receiver (or a separate actuator power supply).

Like the servo motor wires, the Two shielded motor sensor wires provide pulse, and ground. The vast majority of actuator motors do not require power to be hooked to the sensor. Look inside the actuator housing. If there are only two wires connected to the sensor, then hook up pulse and ground to their respective terminals. IF there are three wires connected to the sensor, and pulse and ground interchangeably to the other two sensor wires, then use 3 wires.

The two large stranded wires connect to the large wire terminals at the actuator motor and to the motor wire "M1" and "M2" terminals on the back of the receiver or actuator controller. Now try to move the dish to the east or west; if the dish moves in the direction opposite to the on intended, reverse the wires connected to the motor wire "M1" and "M2" terminals.

 

Guide on Installing a Large C-Band Dish (pdf)

 

Links:

 

Sadoun Digipower SG2100

HH Motors

ACTUATOR SuperJack Dish Motors

Actuators

V-Box Positioner Controller

 

Positioner

Motorized Dish Kits

NOTE: Tighten all the coaxial cable connections only by hand. Using a wrench may over-tighten the connections, causing damage. Such damage is not covered by the Limited warranty.

 

Motorized System FAQ:

 

Do I need a separate power line to connect to the HH Motor?

No.  The motor gets its power from the receiver using the same coaxial cable running from the receiver to the LNBF on the dish.  You simply disconnect the cable from the LNBF.  Connect it to the HH Motor.  Then run a short coaxial cable between the motor and the LNBF.  You are set.

 

How do I control the motor to move it East / West?

The motor is controlled by the receiver's remote control.  All receivers compliant with the DiSEqC 1.2, 1.3, or USALS protocol have the capability to run an HH motor.  Once you initially setup the motor on the satellite arc and store the locations of the satellites, you will be able to move between satellites by simply changing the channel.

 

Does the motor also adjust for variation in elevation on the dish for each satellite?

Yes it does.

 

Do I need to skew the LNBF on a motorized dish?

No you don't.  Just set the skew at 0 and the motor will tilt the whole dish when it moves.

 

What is the benefit from motorizing my dish?

Well, by adding a motor to your system you will be able to receive satellite channels from several satellites instead from one only.  That way you will gain many more channels economically without investing in many dishes and switches.

 

Where can I find out what channels are available free to air?

There are many DVB free to air channels available in North America on satellites such as Galaxy 10R, AMC4, Telstar 5, AMC3, etc. There are channels from the USA and from around the world. See http://www.lyngsat.com/america.shtml for a complete listing of what is available. Any DVB Channel with an
 F  designation is FREE TO AIR.

Channels List

American FTA Channels

English

Arabic Channels

Arabic
Iranian TV Channels
VIETNAM Việt-Nam
European TV channels European
Thai TV Channels สยาม
Korean Channels 한국
Chinese Channels 中国版
Mexican and Spanish Channels

Español

Satellite List

Customer Service

Testimonials

DirecTV

DreamZone Massage Chairs

Sadoun Solar Sales

SatHawk

FlyHawk General Aviation Headsets

Payments Options

Google Checkout

 

  ::::: Setup Guides, Technical Support, and Instructional Videos ::::: 

ZERO-RISK WARRANTY

Comes with a 30-Day Zero-Risk Warranty!
Satisfaction Guaranteed or Your Money Back!

 
 

Use of this website are subject to these Terms & Conditions

About Us | Privacy Statement | Help | FAQ | Fax/Mail Order form | Shipping Information | Return Policy| Careers | Pictures Gallery | Bookmark page | Email to a friend | Free Catalog | Suppliers Inquiries | Contact Us

Sadoun Enterprises LLC

Return to top